Linux version 2.6.32 (2.6.32) (root@pluto) (gcc version 4.6.1 (Debian 4.6.1-10) ) #1 PREEMPT Thu Sep 22 17:56:45 UTC 2011 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 CPU: VIVT data cache, VIVT instruction cache Machine: Philips NAS SPD8020 CC Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 Kernel command line: netconsole=6665@192.168.0.28/,9999@192.168.0.101/ root=/dev/sda14 ro boardType=mv88F6082 productType=Aston reset=0 PID hash table entries: 64 (order: -4, 256 bytes) Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Memory: 8MB 8MB = 16MB total Memory: 12916KB available (2996K code, 179K data, 116K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:64 Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Orion ID: MV88F6082-Rev-A1. TCLK=133333333. bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource orion_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 512 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 512 bind 512) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) msgmni has been set to 25 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled loop: module loaded Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 sata_mv sata_mv.0: version 1.28 sata_mv sata_mv.0: slots 32 ports 1 scsi0 : sata_mv ata1: SATA max UDMA/133 irq 29 physmap platform flash device: 00040000 at f8100000 physmap-flash physmap-flash.0: map_probe failed MV-643xx 10/100/1000 ethernet driver version 1.4 mv643xx_eth smi: probed net eth0: port 0 with MAC address 00:d0:4b:85:8c:da netconsole: local port 6665 netconsole: local IP 192.168.0.28 netconsole: interface eth0 netconsole: remote port 9999 netconsole: remote IP 192.168.0.101 netconsole: remote ethernet address ff:ff:ff:ff:ff:ff netconsole: device eth0 not up yet, forcing it ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: SAMSUNG HD103UI, 1AA01111, max UDMA7 ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD103UI 1AA0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 > sda2 sd 0:0:0:0: [sda] Attached SCSI disk eth0: link up, 1000 Mb/s, full duplex, flow control disabled console [netcon0] enabled netconsole: network logging started ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 input: gpio-keys as /class/input/input0 i2c /dev entries driver rtc-ds1307: probe of 0-0068 failed with error -5 cpuidle: using governor ladder cpuidle: using governor menu Registered led device: power:blue Registered led device: sata0:blue usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: drivers/rtc/hctosys.c: unable to open rtc device (rtc0) EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly on device 8:14. Freeing init memory: 116K kjournald starting. Commit interval 5 seconds Adding 128448k swap on /dev/sda5. Priority:-1 extents:1 across:128448k Adding 1261060k swap on /dev/sda13. Priority:-2 extents:1 across:1261060k EXT3 FS on sda14, internal journal SGI XFS with security attributes, large block/inode numbers, no debug enabled XFS mounting filesystem sda2 EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds